Batik String Quilt Pattern 80 x 90

For awhile now I have been wanting to try a string quilt. I really didn’t want to have to piece it on paper or a fabric foundation so I tried to do it without either. It worked out really well. The reason I think it worked is because I used Batik fabrics and starch.

The size of this quilt is 80 x 90 inches and will be perfect for a summer size quilt top for my bed. Here is what you will need ~

Main Fabric (light) ~ 4 yards (used as the border also)

Fabric for strips. You want a combinations of colors ~ 5 to 6 yards depending on how fat or thin you cut your strips. I cut my strips between 1 3/4 ~ 3 1/4 for variety.

A 12 1/2 inch ruler ~ or some way that you can achieve 12 1/2 inches with a 45 degree line down the middle.

Step one ~  take your main fabric and cut WOF (width of the fabric).  Cut 15 strips at 1 1/2 wide ~ then cut your 1 1/2 inch strips into 18 inches long. You need 30 of these. This is the center of your blocks.

Cut from your fabric strips any width you want by 18 inches long. You need 60 pieces. Now sew a strip of your fabric on both sides of your main fabric. Iron away from the center piece.

Maine Fabric and strips of different colors.

Maine Fabric and strips of different colors.

Now take your 12 1/2 inch ruler and place in the middle of the strip of main fabric on the diagonal. Mark with a pencil the edges of the strip. Shown in photo. (This will be your cutting line once the block is large enough to cut.

#2 Center strip with ruler

#3a second strip mark

Add 1/2 inch to this measurement and cut your next strip this length. Sew into place. Just keep adding until the 12 1/2 inch square is full. If you don’t want to take the time to mark and cut you can cut all your fabric to 18 inch strips and just sew a square that will later be cut on the diagonal.

Mark and measure for next strip

Mark and measure for next strip

Pin and stitch in place

Pin and stitch in place

Once you have 30 squares sewn, then iron with starch, then cut them 12 1/2 x 12 1/2.  Making sure that your light or main fabric is on the diagonal and centered.  Now you are working with a bias edge of the strips.

Square up blocks

Square up blocks


Separate your 30 squares into two piles. Lay them on your cutting board as shown. Notice the main light fabric forms a chevron shape.

Line up your two piles of blocks like this!

Line up your two piles of blocks like this!

Now carefully cut your blocks in half. Should be ******6 1/4 x 12 1/2.

#8b blocks cut

You want to lay them all out to match a pattern in the photo below.

put up on wall string quilt

Next get your main fabric out again and cut 18 strips WOF 1 1/2 inches.  Then sub cut them into 12 1/2 inch lengths. You will need 54 total 1 1/2 x 12 1/2. This is your sashing between the blocks.  Put your sashing up on your design wall between the blocks. Start sewing the rows together. *** Iron toward the sashing.  It is to bulky if you don’t.

sewing sections with sash

Next take your main fabric again and cut 9 strips of 1 1/2 inch fabric. Then sub cut into *****6 1/4 inch lengths. You need 50. Then cut any of your other fabric into 1 1/2 square pieces. Need 45 squares 1 1/2 x 1 1/2.  Start with main fabric and sew 10 of these with 9 squares ending with the main fabric. This is your sash between the rows. Iron toward your main fabric.

small sash

Iron toward sashing less bulk.

Iron toward sashing less bulk.

Sew all the rows and sashing together. Last is the border. Take your main fabric and cut to length of the fabric 4 pieces of 6 1/2 by 84 inches. I  gave you extra length so that if your quilt is a different size this should work. The reason you want to cut by the length of the fabric is because it is the straight of the grain and there is no give so the bias edges around the blocks won’t stretch once it is sewn in place.

***** Important–always measure for your borders. I measured on three sections of the quilt using  the sashing because there is no stretching or out of shape blocks there.

Measure along the sashing

Measure along the sashing

Cut both side sections to the same length.  You need to make the border fit on both sides. You might have had some stretching due to the bias edge blocks. Feed in if necessary. Do the same with the top borders. Your finished!

Finished top

Finished top

finished top

Mine is heading off to my long arm quilter friend because I would like an overall design on it. Feel free to make one! Any questions just ask!

Enjoy and thanks for stopping by.



Filed under Uncategorized

6 responses to “Batik String Quilt Pattern 80 x 90

  1. Patricia

    Great instructions!!!!! Love yours, can’t wait to see it!

  2. Kathy Kinsella

    This is a beautiful quilt, Patricia … and great instructions!

  3. I really like the way this came out!

  4. It’s beautiful. Love your color sense, too

  5. Don’t know where you are but I miss you.

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s