The Story Behind the Quilt ~ Chapter 15: Part Two Trying Something New!

****If you read this already on my WIP post #13 skim to Part Two on the finished quilt!

***** PART ONE

How I design my  quilts  goes something like this:

1. Have a dream about it.

2. Think about it for a day or two.

3.  Just go for it and start! LOL

The quilt I am working on now took me a couple of weeks to figure out how I was going to do it. For those that know me I am not a procrastinator at all. If I think of something I will just go ahead and do it  the next day or within a week. For some reason that didn’t happen with this quilt.

I love Birch trees. Actually I love all trees. I have seen a lot of quilts with trees in them done with different methods. I wanted to try something new to me and not sure if it’s new to you as well. I am right in the middle of this quilt but I wanted to share the steps as I am going along. If you wish to follow me come along and try something new.

The first thing I did was go for a walk around my wooded area and take pictures of birch trees. Just the top half of the tree. I didn’t really want the lower trunk part but the branches and not to many!! Then in my photo shop program I made it black and white. I then went and made it the size that I wanted. Went to my poster program and printed out lots of sheets that I tape together to form the print in the size that I want. This was my template for my branches! I eliminated a lot of the smaller branches and just outlined the larger ones.

Birch tree photo

Birch tree photo

I had some left over white batting (I use Quilter’s Dream Batting) and with a light box, outlined the branches one by one on little pieces of batting with black marker.

Batting is marked and ready for next step!

Batting is marked and ready for next step!

I then covered the batting with two layers of white cheese cloth. There is nothing under the batting, just cheese cloth and batting. After this step I cut up small pieces of black tulle to add to the edges of the branches. This gives it a shadow effect. On top of that I cut small pieces of black hemp and placed them here and there on top of the cheese cloth and black tulle. Then I added one more single layer of cheese cloth on top of that!

tulle and black hemp

tulle and black hemp

last layer cheese cloth

last layer cheese cloth

I then took white thread with my darning foot,  feed dogs down and just went back and forth to form what looked like bark. If you look at birch trees they look like the bark is all going in the same direction. Once I liked the way it looked, I cut along the line of my tree limb. I did learn, with all my threading, that it shrunk my branch quite a bit so the next ones I marked bigger so they would shrink to the right size.

Last I added some fibers of grey and black to the top to give it even more texture.

Extra fibers add more texture to the branch

Extra fibers add more texture to the branch

I had purchased a beautiful piece of dyed fabric going from grey to black to put my branches on.  I am going to leave you here till my next post to explain how I attached the branches to the fabric. I am in the middle of quilting it right now and love the way it is coming out!!

****** PART TWO

Connecting the branches to the background fabric:

First I cut small pieces of Steam a Seam #2 and heat set them here and there to the back of each of the branches. I peeled off the paper to the back of the steam a seam and placed the branches on top of the background piece of fabric. At this point you can move the branches around on the background. Then I took my iron and  heat set them into place. (Please excuse the uneven lighting of this top!) LOL

Branches Attached to the background fabric

Branches Attached to the background fabric

Now it was time to pin baste the quilt. I use small safety pins every 4 inches just to hold the backing, batting and quilt top in place.

I used white thread with  my walking foot to stitch all the branches down. Now was the fun part. How to quilt it!  After looking at my quilt top  I realized I needed one more color to help make it pop a little. I decided on gold and to do leaves throughout the background of the tree.  I did find  a wall stencil template with the leaves I liked. I eliminated some leaves and added some leaves where needed and I made them into a continuous design so I wouldn’t have to stop and start.

gold leaf pattern

gold leaf pattern

After finishing up all the gold leaves I decided to extend the tree branches out into the white border using a light grey thread. There is just enough of a color difference to see the branch. I used a small zig zag stitch free hand, with feed dogs down and a darning foot. I then did a stipple stitch in white thread on the white border and a dark grey on the rest of the quilt. I also did a dark grey zig zag within the tree to create more of the shadow effect.

I did want to say that I bought this beautiful dyed fabric on etsy from Vicki Welsh ~ http://www.etsy.com/shop/vickiwelsh

Here is the finished Tree.

Moonlight Birch Trees

Moonlight Birch Trees

If you would like to see more photo’s of my quilt please visit my etsy shop ~  http://www.etsy.com/shop/thebutterflyquilter

Advertisements

1 Comment

Filed under Uncategorized

One response to “The Story Behind the Quilt ~ Chapter 15: Part Two Trying Something New!

  1. Very lovely. I can’t believe you already finished it. Boy, when inspiration hits you, you don’t mess around! 🙂 Great job!!!

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s